Home > Knowledge > Content

Oil saw operation instructions.

- Mar 13, 2018 -

Oil saw operation instructions.

1. Fill the gasoline tank with a good mixture of oil, and then add the chain lubricant to the fuel tank, and tighten the cover firmly.Note: there is a logo on the top of the tank cap, which is generally larger than the tank cover.2. Dial the circuit switch and switch on the circuit.Note: the position of the domestic oil saw circuit breaker has "STOP" to disconnect the mark.Dial, disconnect the circuit.3. Hold the trigger control arm, press the lock button on the side, and then release the trigger, so that it is in the starting position.4. Pull out the damper and close the damper.Note: when the heat starts, please place the damper on the "open" position.5, please use the left hand firmly hold the machine handle, with foot after living at the bottom of the handle, right hand holding the starting handle, pull to start, when the engine ignition just running again after flameout, the throttle lever back.Note: after pulling, do not suddenly release the hand to prevent damage to the outer cover.6. Pull the start handle again and start the machine.7. Turn off the oil saw and pull the trigger to let the engine idle for a few minutes, turn the switch and disconnect the circuit.

3023.jpg

The oil saw operation needs to know the starting point of the oil saw, and put the mixture into the gasoline tank, then the chain lubricant is added to the fuel tank, and the cap must be tightened firmly.Note: there is a logo on the top of the tank cap, which is generally larger than the tank cover.2. Dial the circuit switch and switch on the circuit.Note: the position of the domestic oil saw circuit breaker has "STOP" to disconnect the mark.Dial, disconnect the circuit.3. Hold the trigger control arm, press the lock button on the side, and then release the trigger, so that it is in the starting position.4. Pull out the damper and close the damper.Note: when the heat starts, please place the damper on the "open" position.5, please use the left hand firmly hold the machine handle, with foot after living at the bottom of the handle, right hand holding the starting handle, pull to start, when the engine ignition just running again after flameout, the throttle lever back.Note: after pulling, do not suddenly release the hand to prevent damage to the outer cover.6. Pull the start handle again and start the machine.7. Turn off the oil saw and pull the trigger to let the engine idle for a few minutes, turn the switch and disconnect the circuit.The carburetor has been adjusted before leaving the factory, but due to the change of operating conditions, it needs to be adjusted slightly.Before adjusting the carburetor, make sure that the air filter and fuel filter are clean, the mixture is fresh and the proportion is suitable.Follow these steps to adjust: 1. Turn off the engine and turn the H and L oil needle until it is not moving., then turn out the H oil needle 1 ring, turn out L oil needle 1 ring and half, restore the original state.(generally, there are three carburetors on the left side of the oil saw, which is the t-idle oil needle. The left side is the L low-speed oil needle, and the right side is H high speed oil needle.)2. Start the engine;3, clockwise turning slowly L oil needle (screwing clockwise rotation speed rise, counterclockwise turn the speed down), find the no-load speed peak position, then L oil needle back a quarter counterclockwise circle.4. Adjust the T screw (turn anticlockwise, and reduce the idle speed;Adjust the oil saw to a stable minimum speed, and the chain does not rotate.5. Adjust the H screw (clockwise, increase the speed and reduce torque;In order to make the cutting force maximum, not to have the highest speed, the cutting test should be done to adjust the effect of H oil needle.(if the mixture concentration is low, the engine speed increases quickly, the exhaust sound is crisp, and the engine torque is small.If the mixture is thick, the engine speed will rise slowly, the high speed will not go, the exhaust sound is dull, smoke.

4000桔灰优点图.jpg

Check that the brake assembly of the oil saw must be brake properly before using the oil saw.When testing brake braking, please release the throttle trigger immediately, so that the oil saw is idle.Check the oil supply condition of the lubricating oil pump before checking the oil supply.Pull the trigger to the medium-speed accelerator, the guide slant to the ground, the lubricating oil spray to the ground, into a straight line.The oil output of the chain lubricant is adjusted by inserting the screwdriver into the hole at the bottom of the clutch side.Rotate counterclockwise to reduce the amount of oil.Note: please adjust according to your work situation.

Related Industry Knowledge

Related Products

  • Rancher 52cc 2-cycle 18-in Gas Chainsaw
  • Showbull 40cc Gas Chain Saw
  • Professional 20 Inch Petrol Chainsaw
  • CG35 Grass Cutting Machine
  • Small Gas Hedge Trimmer
  • 58cc Gas Oregon Chainsaw